1284 Alpine Street Suite A

Cornelius, Oregon 97113

PH: 503-357-0334

Search Our Site

See our work!

Customer Feedback

"Hello dennis you rebuilt my 350 back in june and so far it's been so great to me and performs like a charm! I went by your old shop to show you my truck but they told me you had moved. I wish you great success and thanks again!"

Gutierrez Jorge

Facebook Image

Lifter Installation

Lifter InstallationYou MUST Check Lifter Pre-Load On Any Cylinder Head or Hydraulic Cam Installation!

New engines from the factory can vary as can rebuilt or repaired engines. You can check the following things that could change the height of the plunger in the hydraulic lifter (pre-load):

Cam base circle diameter
Pushrod length
Milled or resurfaced heads, block or both
Faced-off valve stem ends
Thicker or thinner head gaskets
Several valve jobs done on heads
Lifter height difference from lifter manufacturer

Install lifters with a liberal coating of Assembly Lube on the lifter face. Apply motor oil to the lifter's pushrod seat. Lifter adjustments should be made with the intake manifold removed, to better see all valve train motion. Engines with separate adjustable rocker arms, such as the small block and big block Chevy V-8 require installation and adjustment one cylinder at a time! Don't tighten the adjusting nut down before adjusting the valves, since over tightening can cause the valve to hit the piston when the engine is turned over! (This causes bent or broken valves, pushrods, etc.) On engines with shaft mounted adjustable rocker arms you should back off all adjusters all the way before you install the rocker shaft assembly. Be sure the pushrod is seated in the rocker arm seat and tappet before you start to make adjustments! On hydraulic lifter cams, rotate the engine in the normal direction of rotation until the exhaust lifter begins to move UP. Adjust the intake valve to ZERO LASH with no pre-load, then tighten 1/2 more turn. Rotate the engine again until the intake valve has moved ALMOST ALL THE WAY DOWN. Adjust the exhaust valve to ZERO LASH, then 1/2 more turn. Repeat this procedure until each cylinder is completed.

Hydraulic lifter breakdown
On engines with non-adjustable rocker arms you must have a lifter pre-load of .020" to .060". Use the same procedure and sequence as above. Pushrods for each cylinder are usually the same unless valve stem heights are not properly matched. Be sure that the valve you check for lifter pre-load isn't open. Allow a few minutes for lifter bleed down if this occurs. Some installations require changing pushrod length, using adjustable pushrods, shimming the rocker stands or shafts, installing straight screw-in studs instead of stock bottle neck type studs, using Allen set adjusting nuts, or machining the heads for adjustable rocker arms, studs and guide plates.

Hydraulic lifter cams usually do not require additional adjustment after initial engine start-up.

To adjust VALVE LASH ON MECHANICAL LIFTER CAMS (also commonly called "solids" or "flat tappets") follow the same basic procedure as above. Instead of lifter pre-load and zero lash, use the valve lash specs printed on your timing specs card. After engine fire-up, break-in and oil and filter change you'll need to again adjust valve lash, and periodically after that.

Setting Lifter Pre-Load In Hydraulic Lifters On Engines WITHOUT SEPARATE ADJUSTABLE ROCKER ARMS

Lifter pre-load (the distance the pushrod extends into the lifter) should be between .020" and .060". Too little pre-load or no preload will result in very noisy operation while the engine's running. Too much pre-load will cause the engine to idle rough, have very low manifold vacuum and poor low-end performance. It may also stall out when dropped into gear. Torque all bolts for rocker stands, etc., to proper specs. Allow a couple of minutes for the lifters to bleed down, to remove any oil contained inside them. As always, NEW LIFTERS MUST BE INSTALLED ON ANY NEW CAMSHAFT!

Use the valve cover gasket surface of the head as a guide. Lay a metal scribe, etc., flat on this surface. You'll need to make two marks so be sure your reference point is flat and stable. Scribe a line on the pushrod. Unbolt the rocker assembly and loosen up the bolts so the pushrod will stand free in the pushrod seat of the lifter. Note that the pushrod seat in the lifter will be forced up against the snap ring in the top of the lifter by the plunger spring inside the lifter. Scribe another mark on the pushrod. The difference between the two marks is the amount of travel that the pushrod made into the lifter . . . the lifter pre-load! Measure this pre-load amount with a machinist's pocket scale or dial calipers if you have them. .020" to .060" is recommended. If the pre-load is too little measure the amount of free-play between the rocker arm and pushrod and then add .030" to this figure. You can then buy longer than stock pushrods by the amount of extra length you need to achieve pre-load. Remember to add the .030" to the total "longer than stock" length to allow for the extra you need to get the right lifter pre-load! Check one each, intake and exhaust per cylinder head. If your valve stem heights are uneven (check them by measuring from spring seat to the top of the valve) or different from factory specs (see the factory shop manual), then you'll have to check lifter preload on each valve, on both heads.

If you're having a valve job done on your heads have your machinist check the valve stem height. A properly done job should result in a straight edge being laid across the tops of the valve stems with no excessive difference between valve stem tops. On engines with pedestal or shoulder bolt mounted rockers shims can be used to reduce pre-load. If pre-load is too little, or there's none at all you'll need to use longer than stock pushrods. (Use same measuring procedure as above) On engines with individually mounted rockers tighten the adjusting nut or bolt to zero lash. Torque the adjusting nut or bolt into place 3/4 or 1 full turn or rotation. This should put the pushrod at the correct lifter pre-load. If you cannot get .020" to .060" preload you'll have to use shims or longer than stock pushrods. Again, use the previously mentioned procedure to order the correct length pushrods